[ad_1]
When settling cracks in the brick walls, try to get them repointed. This process is called tuck pointing device. However, before any attempt to repair yourself or hire a contractor to carry out repairs or handyman, you must know the top ten most common mistakes made diverted mortar.
The first mistake is to check further problems before the repair. Repair of cracks before checking the plaster and brick of the foundation or other problems occur and thus greater damage to the home and masonry siding.
Settling cracks appear due to the settlement of the foundation and application of the stress of the brick. This makes them a common symptom of foundation repair and may help in understanding where and how much movement the foundation happened.
tuck point along the broken bricks and mortar settle these cracks limits the ability to accurately repair the house foundation. Performing these repairs often result in damage to the brickwork, where the foundation is repaired. Mortar and bricks placed and cracks will fill the gap wedge and force the opposite cracks to form in the area and the brick tend to crowd out the corners of the house caused by the brick walls crack, lean away from the house or come off the foundation altogether when the house is highlighted.
can not stress enough to check for other problems with the structure or foundation before the home repair cracks in the mortar.
The second most common mistake in choosing a recording of settling cracks in brick foundation repair company at the foundation. Is there a difference in leveling the base of the house and fixing foundation problems.
There was never even built a house foundation is perfectly level, that I’m aware of, and level with the foundation of the house would apply stresses to the home and cause more problems with your foundation. This is even more cracks in the bricks and mortar joints around your home. When I emphasize the word level, and use the computer at the readings, this is a strong indication that they intend to try leveling the foundation, if it does not cause more problems. If you focus on lifting, stabilizing, adjusting and use the cracks in the plaster and bricks to gain range of motion in the House floor, it is probably a more accurate account of the details of the move and have a better chance of providing quality foundation repair services.
The third common mistake brick repair these pipes plaster repair sealant to try to repair the crack yourself. While sealant is used around doors and windows and check the expansion joints to seal the wall and still allows you to move, they do not intend to use the mortar and cause damage to the brick.
Sealing the grout and never look tends to be difficult to clean off his face because of the texture of bricks. The same is true for many other masonry repair products. These include adhesives, epoxy, and other additional mixtures that can be difficult to work with and difficult to remove. This often removes all the bricks in the areas where these products are used to repair the brick. If you want to improve the mortar cracks yourself, you should use the appropriate redirection mortar of the same composition as the original. These are not big things that are custom made to your composition mortar, mortar and require appropriate analysis of existing mortar samples.
Improving the fourth wall there is an error, how to comply with the grout. This is not to be confused with the right grout color. Mortar suitable for the process of analyzing samples of mortar identify their composition, performance, and formula. As the color of the sand and other materials in the composition of the color effects, are connected to each other, but wherein the base be matched to a mortar composition, before any attempt is made to match the color to an existing mortar.
The composition and formulation of the mortar instructions to the appropriate repair mortar and maintaining the formula. This is important because if the grout is different and a different composition than the original mortar, even the complications that the color is more difficult to match, cause damage to the brick to prevent new mortar bonds the old plaster, and would allow the wall to fall, if the grout crash.
corresponding to the fifth most common troubleshooting masonry mortar color. Most of the time analyzing the composition of the original mortar mortar skipped and general assumptions in place. This difficulty matching mortar color, because the color of the direct result of the composition and the ratio of substances in the mortar. To match the color of the grout, it must first match the existing formula and the composition of the mortar.
After the base formula and the composition, by setting the color of the mortar materials and color pigments are added, if necessary. However, a common mistake by adding pigments or other material too quickly or change a formula basis. It must adhere to maintain the performance of the base formula and mortar type is produced, and do not forget to add every part slowly, we will continue with it, but you do not know anything back.
Improving the masonry, the sixth most common mistake is to improve the depth. The patch or bandage covering the top of a problem, but repair the cracks, you need to remove some of the existing mortar. It should be removed to a depth that allows a good bond to the new mortar to old brick and mortar. This will help ensure the long-term repair of masonry. Generally, a good depth of about 1 / 2-3 / 4 inch deep into the mortar joints. The more is better, especially if the gap makes it possible to replace the whole joint mortar.
The seventh item where the errors occur in the preparation of the cracks in the transfer. Dust and debris in order to avoid new cracks in the mortar joints of the old cement mortar joints and prevent the filling completely. It is important to brush away any loose debris or dust, and rinse and moisten the old plaster. This will help the new mortar binding the existing mortar.
The eighth error often made of mortar mixes. Too often, water is added rapidly and exceeding the required amount, and an attempt is made to adjust this. The most common attempt to correct the problem is to add sand or mortar mix. If this formula is changed, the composition and the resulting mortar does not meet the requirements.
If you add too much water, you need to add more formula based on the total composition of materials to stop this without changing the ratio and mortar type. It is best to slowly add water or pigments can not remove them, and when mistakes like this happens, it may be better to throw the mortar and restart.
The ninth biggest mistake made in the announcement of the tuck pointing mortar joint completely. Where the application of the mortar joints, may seem complete, but must be packed to the mortar joints are tight. The dust and debris to prevent this and must be cleaned before installing the new mortar.
When the mortar joints are not completely filled, they tend to crumble when pressure is applied. This is often noticed when tooling the mortar joints if the grout started to tighten in front of the wall, grout or mold takes place. If you noticed, remove the grout where it occurs, and replace it with a new one. Also, remember to begin to stiffen, it does not mean to be hard before tooling the joints. Pressure dry mortar, which can not be cured due to cracking or crumbling plaster and must be replaced.
and the tenth most common mistake brick mortar repair tooling and brushing the mortar joints. As mentioned earlier, the tool must be made as the mortar begins to stiffen, but before the tool is too hard. However, when the tooling of the mortar, it is important to match the types of existing tools. There are various designs of instruments that shape the mortar joints. Most frequently a round or raked mortar joint. You should use the pointer tool, in which the right design and size of the mortar joint. These devices come in a wider angle thicker grouting.
This is important to make the repairs blend into the wall. A jointer, a result that does not match the mortar to cast a shadow on the nodes of the new and old plaster. This may occur if the mortars member or excess mortar that pressed deposition tools. It is necessary to wash away the excess and blend the edges of all common mortar to match the repairs properly.
As you can see, repairing masonry is a very detailed process where a small deviation in any significant change to the details coming out of the repair.
[ad_2]
Source by James Nech